+1 437 696-3515 Request an estimate

Article · November 8, 2026

Stains on a PVC membrane pool: what the mark tells you and what the makers allow

The waterline, the floor under leaves, the drain, a wide patch: what each stain usually means, and what RENOLIT and SOPREMA say you can and can't use on it.

An empty pool lined in blue mosaic-pattern membrane with an infinity edge and wide white-edged steps, two people sitting on the steps in front of a large house with columns

On a concrete pool, a stubborn stain can be scrubbed hard or washed off with acid. On a reinforced PVC membrane you can't do either, so the first useful thing is to look at where the mark sits. Position tells you more than colour, and it tells you which of the makers' rules you broke, if any.

Start with where the mark is

Where you see itWhat usually causes itFirst thing to do
A ring along the waterlineSunscreen, body oil and dirt, sometimes with calcium on topClean it with a soft cloth or sponge and a membrane cleaner, then check the hardness of the water
Brown patches on the floor, in the shape of leavesLeaves that lay on the bottom for weeks, often over the winterGet the debris out, bring the water back into balance and give it time with the filter running
Around the main drain or under where a floater satChemicals that stayed in one place at high strengthChange how you dose, as described further down
Blue-green, brown or grey patches spread over walls and floorMetal dissolved in the waterHave the water tested for iron and copper before you add anything
Dark spots that you can't reach because they seem to be inside the surfaceGrowth between the membrane and the shell behind itCall the installer, as cleaning from the water side won't reach it
The colour fading evenly over the whole poolToo much chlorine over a long time, or water kept very warmNot a stain to remove: correct the water

A table like this only narrows it down. A water test from a pool store or a lab settles the metal question, and the rest of this article goes through each case with what RENOLIT and SOPREMA write in their own documents.

Metal in the water

This is the case to take seriously, because the makers are frank about how it ends. RENOLIT writes in the data sheet for its ALKORPLUS Anti-Stain product that metal stains on a liner are

very difficult, if not impossible, to remove.

So with metal, the work happens before the stain. RENOLIT and SOPREMA between them name these ways it gets into a pool:

  1. Well water used to fill or top up the pool. SOPREMA strongly recommends water from the public supply for that reason.
  2. Water treatment products that contain copper, including some algaecides and disinfection systems. Both makers tell you to avoid them.
  3. Corroded pipes, pumps or heat exchangers.
  4. Impurities in ordinary pool chemicals.
  5. Mains water itself, which RENOLIT notes can carry up to 0.2 ppm of copper.

SOPREMA's maintenance instructions for its reinforced membrane give a number to work with: once the pool is filled, test it for iron and copper, and if either is above 0.02 mg/L, treat the water with a metal sequestrant. RENOLIT's product works a little differently. It goes into the skimmer, sits in the filter as a layer and takes the metal out when you backwash, so a fresh dose follows every backwash.

If your house runs on a well

Health Canada's page on testing your well water lists iron and hardness among the general water quality values, asks for those to be tested every 2 years through an accredited lab or the public health unit, and names staining as one of the reasons people treat for them. If you have that report, it tells you a lot about your pool before you fill it. If you don't, it's worth ordering before the spring fill, or having the water trucked in from the public supply.

A test RENOLIT gives you for your own chemicals

The same RENOLIT data sheet describes a way to check whether a pool product you already own carries heavy metals. It uses the Anti-Stain liquid, so you need a bottle of it.

  1. Do it outside. Some acid products give off an unpleasant smell when mixed.
  2. Pour 5 ml of the product into a glass. A powder or tablet: dissolve 1 g in 5 ml of water.
  3. Add 3 drops of the Anti-Stain and mix for about 15 seconds.
  4. Wait 10 minutes. The Anti-Stain is white. If it has gone grey, the product contains heavy metals.

Never mix the Anti-Stain itself with an acid. RENOLIT warns that this gives off an irritating gas that can catch fire.

The sheet adds one more warning that matters for anyone who has just closed a pool. Don't leave chlorine tablets in the skimmer outside the season, or any time the pump isn't running regularly. The chlorine builds up, corrodes metal parts of the pump, and that metal ends up in the water. Our article on closing a membrane pool for winter has the rest of the closing routine.

The ring at the waterline

SOPREMA puts sunscreen and tanning oil at the top of its warnings for the waterline. They leave a line that gets harder to remove once calcium settles on it. Hard water does that on its own too, as white deposits, which is why SOPREMA keeps hardness between 175 and 230 ppm.

RENOLIT's care tips for ALKORPLAN membrane describe the cleaning plainly: a damp non-abrasive cloth with its ALKORCLEAN degreaser on the dirty band. Limescale wants an acid-based product, and for that RENOLIT sends you to a maintenance company or a specialist chemical supplier. A shower before swimming cuts down on the oil in the first place.

On light membrane, copper and sunscreen together can turn the waterline yellow for good. We covered that with the other colour questions in choosing a membrane colour.

Stains that start behind the membrane

Some dark spots can't be cleaned because they are not on the surface at all. RENOLIT explains that moisture collects between the shell and the liner, and that organic matter there lets micro-organisms grow. Its answer is to clean and disinfect the shell before the membrane goes on.

A pool wall covered in blue felt-like underlay with a round white wall fitting set into it and a strip of blue membrane along the top edge
The underlay goes onto the bare shell first, and the membrane is welded over it.

We lay a geotextile underlay over the shell before the membrane. You can see it on our pool installation page, and how an old shell is prepared is on the page about pool renovation with membrane. If spots appear from behind on a pool that is already lined, send us photographs: it's a question for the people who can see under the membrane.

What should never touch the membrane

Most marks that never come out were made by something that sat in one place. SOPREMA is direct about it: no chemical product, liquid or solid, should touch the membrane.

  • Chlorine tablets go in the skimmer, with filtration running until they have dissolved.
  • Floating dispensers are strongly discouraged. They drift into one spot and stay there.
  • Granular chemicals thrown onto the water sink and rest on the floor.
  • Metal brushes, corrosive sponges and pressure washers damage the surface.
  • Copper-based treatments, for the reasons above.
A square metal drain grate with a pattern of slots, set flush into grey stone-pattern pool membrane
A main drain in stone-pattern membrane. When the pump stops, chemicals collect around it.

That last point about filtration is why a stain so often shows up around the main drain. SOPREMA notes that when filtration stops, chemicals concentrate near the drain and can damage the lining. Too much chlorine over time does the same to the whole surface: the sheet links excess chlorine to discolouration and a low pH to water that attacks the lining, and it keeps pH between 7.2 and 7.6 with stabilised chlorine at 0.7 to 1.5 mg/L. Water kept above 32°C makes all of it worse.

When a mark won't come out

A stain that stays after the water is balanced, tested and cleaned for metal is part of the membrane now. Look at it closely while you're there: a mark that follows a seam or circles a fitting can be a sign of something else, and seams, fittings and wrinkles are what our membrane repair work deals with. When the whole surface has faded or is marked all over, a new membrane over the old pool is the cleaner answer.

Can I drain the pool to scrub a stain off the floor?

No. SOPREMA advises against leaving a membrane pool empty at any time. Without water the membrane takes the sun and anything that falls in, and if rain or groundwater gets in behind it, it can shift and fold. Stains on the floor are treated with the water in.

Will a stain remover hurt the membrane?

Use one the membrane maker names or approves, and follow its label. Strong acid products, the kind sold against limescale, are a job for a pool maintenance company or a specialist supplier, as RENOLIT puts it, and no product should be poured straight onto the membrane.

If you're not sure what you're looking at, take a photo of the mark close up and another of the whole pool, and tell us which membrane you have. The makers we work with are on our membranes page.

Tell us about your pool

Every estimate is prepared by us, after we have reviewed the pool. Send photographs if you have them.

+1 437 696-3515
Call Request an estimate